设为首页 | 加入收藏 | 返回首页
请稍候...
  • 陕西卓源电气科技有限公司
  • 陕西卓源电气科技有限公司
  • 陕西卓源电气科技有限公司
  • 陕西卓源电气科技有限公司
  • 陕西卓源电气科技有限公司
  • 陕西卓源电气科技有限公司
栏目导航
联系我们

陕西卓源电气科技有限公司

地址:西安市高新技术开发区锦业路568号

手机:185 9196 3772
      186 2900 8585

      133 7923 0068

座机:029-87545305

邮箱:sxzydqkj@163.com 

 

变压器智能风冷控制柜 你现在的位置:首页 - 产品展示 - 变压器智能风冷控制柜

ZY-W-100温湿度控制器

图集简介

ZY-W-100温湿度控制器

温湿度控制器ZY -W - 100
The temperature and humidity controller ZY-W-100
一.主要功能The primary functions
带一路温度传感器和一路凝露传感器, 随时监测环
境的温湿度变化情况, 当湿度达到一定或温度变化剧增
, 有产生凝露的可能时, 控制器驱动加热器, 破坏产生
凝露的条件。当产生凝露的条件消失后, 加热器自动断
开, 控制器恢复到监测状态。
The first temperature transducer and the dew sensor, always check to see the environmental changes in temperature or humidity, when the humidity got higher and higher,or the temperature is greatly changed and can run drew, the heater of controller to cause interference. when unfavourable factors disappeared, the heater automatic breaking-off and the state of being restored.
二.技术指标The technique index

1、供电电源:A C 2 3 0 V±1 0 %(6 0 H z)
Power supplies: A C 2 3 0 V±1 0 %( 6 0 H z)
2、工作环境:温度- 2 0℃ ~7 0℃湿度≤9 5 % R H
Environment: temperature: - 2 0℃ ~7 0℃, humidity: ≤9 5 % R H
3、温区控制范围:5℃~2 0℃
The range of scream temperature: 5℃~2 0℃
4、温度控制精度:±1℃
The control precision: ±1℃
5、湿度控制范围:1 0 % R H~9 5 % R H 凝露启控:≤9 5 % R H
The range of humidity: 1 0 % R H~9 5 % R H drew arrested: ≤9 5 % R H
6、输出接点:阻性A C 2 2 0 V,3 A
Contact output: Resistive A C 2 2 0 V,3 A
7、功耗:≤2 W
Consumption: ≤2 W
8、可靠安全性:符合I E C 8 3 4 - 1要求
Safety testing: Conform to I E C 8 3 4 - 1
9、外形尺寸:4 8×4 8×9 0
Overall dimensions:4 8×4 8×9 0
1 0、开孔尺寸:4 5×4 5
Perforation size: 4 5×4 5
三.安装使用Installation
接线图wiring diagram
面板式安装 micropanel Installation 底座式安装foundation installation






四.传感器的安装The Installation of transducer
1、凝露传感器 The dew transducer
(1)将传感器两则,用4 M固定在被测器件的壳体上。
The side of transducer was fixed in the shell with 4M
(2)将传感器插入导轨槽里。
The transducer put in single channel
(3)温度传感器安装方式与凝露传感器相同
The way of temperature transducer installation is same to the dew sensor.
(4)注:内置传感器无需用户安装。
Note: The built-in transducer without user installation.
五、使用方法application
1、按图接线,通电后,开启指示灯亮,满足加热条件,
表示加热器工作。
Follow the wiring diagram, the power has been turn on, the indicator lights up, meet the conditions for heating, and express the heater is normal work.
2、如需试验凝露感湿后的加热工作情况,在温度大于
20度环境中,可将凝露传感器放入冰箱约5分钟后取出,
来模似凝露条件,或用对凝露传感器哈气的方法进行,
观察凝露条件下的工作情况
If need to test the heating work when the drew feeling the dry ,in the environment if the environment temperature is high than 20℃,you can put the dew sensor in the refrigerator about five minutes to simulate drew conditions,or blew against the dew sensor, to observations work in the dew conditions.


详细说明
 

温湿度控制器ZY - W - 1 0 0

The temperature and humidity controller ZY-W-100

.主要功能The primary functions

带一路温度传感器和一路凝露传感器, 随时监测环

境的温湿度变化情况, 当湿度达到一定或温度变化剧增

, 有产生凝露的可能时, 控制器驱动加热器, 破坏产生

凝露的条件。当产生凝露的条件消失后, 加热器自动断

开, 控制器恢复到监测状态。

The first temperature transducer and the dew sensor, always check to see the environmental changes in temperature or humidity, when the humidity got higher and higher,or the temperature is greatly changed and can run drew, the heater of controller  to cause interference. when unfavourable factors disappeared, the heater automatic breaking-off and the state of being restored.

.技术指标The technique index

 

1、供电电源:A C 2 3 0 V±1 0 %6 0 H z

   Power supplies: A C 2 3 0 V±1 0 % 6 0 H z

2、工作环境:温度- 2 0 7 0湿度≤9 5 % R H

Environment: temperature: - 2 0 7 0, humidity: 9 5 % R H

3、温区控制范围:5℃~2 0

   The range of scream temperature: 5~2 0

4、温度控制精度:±1

   The control precision: ±1

5、湿度控制范围:1 0 % R H9 5 % R H 凝露启控:≤9 5 % R H

   The range of humidity: 1 0 % R H9 5 % R H drew arrested: 9 5 % R H

6、输出接点:阻性A C 2 2 0 V3 A

   Contact output: Resistive A C 2 2 0 V3 A

7、功耗:≤2 W

   Consumption: 2 W

8、可靠安全性:符合I E C 8 3 4 - 1要求

   Safety testing: Conform to I E C 8 3 4 - 1

9、外形尺寸:4 8×4 8×9 0

   Overall dimensions:4 8×4 8×9 0

1 0、开孔尺寸:4 5×4 5

     Perforation size: 4 5×4 5

.安装使用Installation

接线图wiring diagram

面板式安装   micropanel Installation        底座式安装foundation installation

 

 

 

 

 

 

.传感器的安装The Installation of transducer

1、凝露传感器 The dew transducer

1)将传感器两则,用4 M固定在被测器件的壳体上。

     The side of transducer was fixed in the shell with 4M

2)将传感器插入导轨槽里。

     The transducer put in single channel

3)温度传感器安装方式与凝露传感器相同

     The way of temperature transducer installation is same to the dew sensor.

 4)注:内置传感器无需用户安装。

     Note: The built-in transducer without user installation.

五、使用方法application

1、按图接线,通电后,开启指示灯亮,满足加热条件,

表示加热器工作。

Follow the wiring diagram, the power has been turn on, the indicator lights up, meet the conditions for heating, and express the heater is normal work.

2、如需试验凝露感湿后的加热工作情况,在温度大于

20度环境中,可将凝露传感器放入冰箱约5分钟后取出,

来模似凝露条件,或用对凝露传感器哈气的方法进行,

观察凝露条件下的工作情况

If need to test the heating work when the drew feeling the dry ,in the environment if the environment temperature is high than 20,you can put the dew sensor in the refrigerator about five minutes to simulate drew conditions,or blew against the dew sensor, to observations work in the dew conditions.

打印本页 | 返回前一页

网站首页  |  新闻中心  |  关于我们  |  产品中心  |  最新图集  |   联系我们  |  返回顶部

Copyright (C) 2014. 陕西卓源电气科技有限公司 版权所有 网站维护:西北大网 - 西安网 - 陕ICP备2020015985号
陕公网安备 61019002001421号